Shelly Wave 2PM

Note: The product line known as "Shelly Qubino Wave" will now be referred to as "Shelly Wave". This name change will not impact the functionality of any devices. The only modification will be the use of the new name in all future documentation.

Device Identification

• Device name: Wave 2PM
• EU Part number/Ordering Code: QNSW-002P16EU
• Z-Wave Product type ID: 0x0002
• Z-Wave Product ID: 0x0081
• Z-Wave Manufacturer: Shelly Europe Ltd.
• Z-Wave Manufacturer ID: 0x0460

Terminology

• Device – In this document, the term “Device” is used to refer to the Wave 2PM device.
• Gateway – A Z-Wave® gateway, also referred to as a Z-Wave® controller, Z-Wave® main controller, Z-Wave® primary controller, or Z-Wave® hub, etc., is a device that serves as a central hub for a Z-Wave® smart home network. The term “gateway” is used in this document.
• S button – The Z-Wave® Service button, which is located on Z-Wave® devices and is used for various functions such as adding (inclusion), removing (exclusion), and resetting the device to its factory default settings. The term "S button" is used in this document.

Short Description

The Wave 2PM (Device) is a single product that enables remote control of two electrical devices such as bulbs, ceiling fans, and IR heaters. It switches (on/off) two independent loads and measures their power consumption separately and in total. The Device is compatible with switches (default) and push-buttons.

Switch connected to input terminal SW (SW1)

If the SW (SW1) is configured as a switch (default), each toggle of the switch will change the output state O (O1) to the opposite state – ON, OFF, ON, etc.

• Change switch position once: Change the state of the output state O (O1) to the opposite one and send command to the associated devices in associated groups 2 and 3 (check chapter Z-Wave Association).

Switch connected to input terminal SW2

If the SW (SW1) is configured as a switch (default), each toggle of the switch will change the output state O2 to the opposite state – ON, OFF, ON, etc.

• Change switch position once: Change the state of the output state O2 to the opposite one and send command to the associated devices in associated groups 2 and 3 (check chapter Z-Wave Association).

Main Applications

• Residential
• MDU (Multi Dwelling Units - apartments, condominiums, hotels, etc.)
• Light commercial (small office buildings, small retail/restaurant/gas station, etc.)
• Government/municipal
• University/college

Integrations

Shelly Qubino Wave devices are developed on the world's leading technology for smart homes – Z-Wave.
This means Shelly Qubino Wave works with all certified gateways supporting Z-Wave communication protocol.
To make sure the functions of Shelly Qubino Wave products are supported on your gateway, we are regularly executing compatibility tests of our devices with different Z-Wave gateways.

Simplified Internal Schematics

Device Electrical Interfaces

Inputs

• 2 switch/button input on screw terminal
• 3 power supply inputs on screw terminals: N (+) and L (Ʇ)

Outputs

• 2 relay output with power measurement on screw terminal

Connectivity

Z-Wave – Unsecure, S0 Security, S2 Unauthenticated Security, S2 Authenticated Security

Safety Features

Overheat Protection

• Switch off its own relay
• Send Notification Report to the Gateway (Overheat detected)
• LED lights react as specified above (check blinking mode for Overheat detected)

Any of the following activities reset this alarm: power cycle, short press on S button, press any switch-push button connected to any SW (SW, SW1, SW2, …) terminal.

NOTE: The Overheat protection is always active and cannot be disabled.
Additional description above under chapter Notification for Overheat detected.

Over-current Protection

Device has internal Over-current protection. If the current exceeds 16A+10% (Max switching current +10%) for more than 5s, the Device will:

• Switch off its own relay
• Send Notification Report to the Gateway (Over-current detected)
• LED lights react as specified above (check blinking mode for Over-current detected)

Any of the following activities reset this alarm: power cycle, short press on S button, press any switch-push button connected to any SW (SW, SW1, SW2, …) terminal.

NOTE: The Over-current protection is always active and cannot be disabled.
Additional description above under chapter Notification for Over-current detected.

Supported Load Types

• Resistive (incandescent bulbs, heating devices)
• Capacitive (capacitor banks, electronic equipment, motor start capacitors)
• Inductive with RC Snubber (LED light drivers, transformers, fans, refrigerators, air-conditioners)

User Interface

S Button and Operating Modes

1. Normal mode
2. Setting in progress mode
3. Setting mode (with S button)
   • Settings mode is required to start desired procedure (e.g., adding/inclusion, removing/exclusion, factory reset). It has a limited time of operation. After the procedure concludes, the Device automatically returns to Normal mode.
   • Entering Setting mode:
     • Quickly press and hold the S button until the LED turns solid blue.
     • An additional quick press on the S button means menu change in infinite loop.
     • Menu LED status has a timeout of 10s before returning to Normal state.

S Button’s Functions

• Manually add the Device to a Z-Wave network
• Manually remove the Device from a Z-Wave network
• Factory Reset the Device

LED Signalisation

Click to see LED signalisation

Normal Mode

• Removed/Excluded
  The LED will be blinking blue in Mode 1 for 10 min after every power cycle and 10 min after S button pressed.
  

• Added/Included
  The LED will be blinking green in Mode 1 for 10 min after every power cycle and 10 min after S button pressed.
  

Settings in Progress

• Factory reset and reboot
  During factory reset, the LED will turn solid green for approx. 1 sec, then blue and red LEDs will blink 0.1s On / 0.1s Off for about 2 sec.

• Adding / Removing
  During adding or removing, the LED will be blinking blue in Mode 2.
  

• Firmware updating OTA
  During OTA update, the LED will be blinking blue and red in Mode 2.
  

• Checking power supply 230 V AC frequency or 24 V DC voltage
  During checking, the LED will be blinking blue and red in Mode 5.
  

Settings Mode with S Button

• Adding / Removing menu selected
  When the menu is selected, the LED will be solid blue, for up to 10 seconds.

• Adding / Removing – while pressing S button – Add/Remove process selected
  When the menu is executing, the LED will be blinking blue in Mode 3.
  

• Factory reset menu selected
  When the menu is selected, the LED will be solid red, for up to 10 seconds.

• Factory reset – while pressing S button – Factory reset process selected
  When the menu is executing, the LED will be blinking red in Mode 3.
  

Alarm Mode

• Over-current detected
  The LED will be blinking red in Mode 4: 1x (0.2s On / 0.2s Off) + 2s Off, repeating.
  

• Overheat detected
  The LED will be blinking red in Mode 4: 2x (0.2s On / 0.2s Off) + 2s Off, repeating.
  

• Power supply fault (power supply 230 V AC frequency or 24 V DC voltage fault)
  The LED will be blinking red in Mode 4: 3x (0.2s On / 0.2s Off) + 2s Off, repeating.
  

LED Blinking Modes

Click to see the LED blinking modes

Mode	Blinking Pattern
Mode 1	0.5s On / 2s Off
Mode 2	0.5s On / 0.5s Off
Mode 3	0.1s On / 0.1s Off
Mode 4	(1x to 6x: 0.2s On / 0.2s Off) + 2s Off
Mode 5	0.2s On blue / 0.2s On red

Specifications

Feature	Specification
Power supply	110–240 V AC / 24 V DC ±10%
Power consumption	< 0.3 W
Power measurement [W]	Yes
Max switching voltage AC	240 V
Max switching current AC	10 A per channel, 16 A total, 18 A total peak
Max switching voltage DC	30 V
Max switching current DC	10 A
Overheating protection	Yes
Over-current protection	Yes
Over-voltage protection	Yes
Distance	Up to 40 m indoors (131 ft.) (depends on local conditions)
Z-Wave® repeater	Yes
CPU	Z-Wave® S800
Z-Wave® frequency band	868.4 MHz
Max radio frequency power transmitted	< 25 mW
Size (H x W x D)	37 x 42 x 16 ±0.5 mm / 1.46 x 1.65 x 0.63 ±0.02 in
Weight	29g
Mounting	Wall console
Screw terminals max torque	0.4 Nm / 3.5 lbin
Conductor cross section	0.5 to 1.5 mm² / 20 to 16 AWG
Conductor stripped length	5 to 6 mm / 0.20 to 0.24 in
Shell material	Plastic
Colour	Black
Ambient temperature	-20°C to 40°C / -5°F to 105°F
Humidity	30% to 70% RH
Max altitude	2000 m / 6562 ft.

Basic Wiring Diagram

Diagram 1	Diagram 2

Diagram 3	Diagram 4

Legend

Terminals	Description	Wires	Description
N	Neutral terminal	N	Neutral wire
L	Live terminal (110–240 V AC)	L	Live (110–240 V AC) wire
SW 1	Switch/push-button input terminal (controlling O1)	+	24 V DC positive wire
SW 2	Switch/push-button input terminal (controlling O2)	GND	24 V DC ground wire
O1	Load circuit 1 output terminal
O2	Load circuit 2 output terminal
+	24 V DC positive terminal
Ʇ	24 V DC ground terminal

About Z-Wave®

Adding the Device to a Z-Wave® Network (Inclusion)

Note! All Device outputs (O, O1, O2, etc.) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave® network.

Note! In case of Security 2 (S2) adding (inclusion), a dialog will appear asking you to enter the corresponding PIN Code (5 underlined digits) written on the Z-Wave® DSK label on the side of the Device and in the packaging.
IMPORTANT: The PIN Code must not be lost.

SmartStart Adding (Inclusion)

SmartStart enabled products can be added into a Z-Wave® network by scanning the QR code on the Device with a gateway providing SmartStart inclusion. No further action is required; the device will be added automatically within 10 minutes of being switched on in the network vicinity.

1. With the gateway app, scan the QR code on the Device label and add the Security 2 (S2) Device Specific Key (DSK) to the provisioning list.
2. Connect the Device to a power supply.
3. Check if the blue LED is blinking slowly. If so, the Device is not added.
4. Adding is initiated automatically within seconds after connecting to power.
5. The blue LED will blink faster during the adding process.
6. The green LED will blink slowly if the Device is successfully added.

Adding (Inclusion) with the S Button

1. Connect the Device to a power supply.
2. Check if the blue LED is blinking slowly. If so, the Device is not added.
3. Enable add/remove mode on the gateway.
4. To enter Setting mode, quickly press and hold the S button until the LED turns solid blue.
5. Release, then press and hold (>2s) the S button until the blue LED starts blinking slowly. Releasing the button starts Learn mode.
6. The blue LED will blink faster during the adding process.
7. The green LED will blink slowly if successful.

Note: In Setting mode, the Device has a timeout of 10s before returning to Normal mode.

Adding (Inclusion) with a Switch/Push-button

1. Connect the Device to a power supply.
2. Check if the blue LED is blinking slowly. If so, the Device is not added.
3. Enable add/remove mode on the gateway.
4. Toggle the switch/push-button connected to any SW terminal (SW, SW1, SW2, etc.) 3 times within 3 seconds (this puts the Device in Learn mode). The Device must receive on/off signal 3 times.
5. The blue LED will blink faster during the adding process.
6. The green LED will blink slowly if successful.

Learn mode – a state allowing the Device to receive network information from the gateway.

Removing the Device from a Z-Wave® Network (Exclusion)

Note: The Device will be removed from your Z-Wave® network, but any custom configuration parameters will not be erased.

Note! All Device outputs (O, O1, O2, etc.) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave® network.

Removing (Exclusion) with the S Button

1. Connect the Device to a power supply.
2. Check if the green LED is blinking slowly. If so, the Device is added.
3. Enable add/remove mode on the gateway.
4. To enter Setting mode, quickly press and hold the S button until the LED turns solid blue.
5. Release, then press and hold (>2s) the S button until the blue LED starts blinking slowly. Releasing the button starts Learn mode.
6. The blue LED will blink faster during removal.
7. The blue LED will blink slower if successful.

Note: In Setting mode, the Device has a timeout of 10s before returning to Normal mode.

Removing (Exclusion) with a Switch/Push-button

1. Connect the Device to a power supply.
2. Check if the green LED is blinking slowly. If so, the Device is added.
3. Enable add/remove mode on the gateway.
4. Toggle the switch/push-button connected to any SW terminal 3 times within 3 seconds (this puts the Device in Learn mode).
5. The blue LED will blink faster during removal.
6. The blue LED will blink slower if successful.

Factory Reset

General

After Factory reset, all custom parameters and stored values (kWh, associations, routing, etc.) return to default. HOME ID and NODE ID assigned to the Device will be deleted. Use this only when the gateway is missing or otherwise inoperable.

With the S Button

Note: Factory reset with the S button is possible anytime.

1. Press and hold the S button until the LED turns solid blue.
2. Press the S button multiple times until the LED turns solid red.
3. Press and hold (>2s) the S button until the red LED starts blinking faster. Releasing the button starts the reset.
4. During reset, the LED turns solid green for ~1s, then blue and red blink faster for ~2s.
5. The blue LED will blink slower if successful.

With a Switch/Push-button

Note: Factory reset with a switch/push-button is only possible within the first minute after power-up.

1. Connect the Device to a power supply.
2. Toggle the switch/push-button connected to any SW terminal 5 times within 3 seconds.
3. During reset, the LED turns solid green for ~1s, then blue and red blink faster for ~2s.
4. The blue LED will blink slower if successful.

Remotely via Parameter

Factory reset can be done remotely by setting Parameter No. 120.

Z-Wave® Security and Device Specific Key (DSK)

The Device supports the latest Security 2 (S2) feature. S2 uses strong AES 128 Encryption, making Z-Wave® the most secure IoT platform.

• Authenticated Control
  • Out-of-band DSK for inclusion
  • May be used by most implementations

The Device supports Security 2 Authenticated, Unauthenticated, and Unsecure adding (inclusion).

Note: When adding the Device to a Z-Wave network with a gateway supporting S2, the PIN Code of the Z-Wave Device Specific Key (DSK) is required. You can find it on the label on the side of the Device and in the packaging. Do not remove the DSK label.

The first five digits of the key are highlighted or underlined to help identify the PIN Code part. The DSK is additionally represented with a QR Code.

DSK Label and QR Code (Example)

Joining node requesting to join the S2 Access Control Class or S2 Authenticated Class will obfuscate its Public Key by setting bytes 1..2 to zeros (0x00) before transferring via RF.

The DSK may be used for out-of-band (OOB) authentication.

• The including gateway may use a QR code scanner to read the entire DSK and match it with the obfuscated public key received via RF.

Z-Wave® Parameters

Parameter	Description
No. 1 – SW (SW1) Switch Type	Defines how the Device treats the switch on SW (SW1). Default: 2 Values: 0 = momentary, 1 = toggle (contact closed=ON), 2 = toggle (device changes status on switch change)
No. 2 – SW2 Switch Type	Same as above for SW2. Default: 2
No. 6 – Inputs SW1 & SW2 Swap	Swap operation of SW1 and SW2 without rewiring. Default: 0 (SW1-O1, SW2-O2) Value: 1 → swapped
No. 16 – Outputs O1 & O2 Swap	Swap operation of O1 and O2 without rewiring. Default: 0 Value: 1 → reversed
No. 17 – Restore O (O1) State After Power Failure	Determines if last state is saved/restored. Default: 0 (save and restore) Value: 1 → remains off
No. 18 – Restore O2 State After Power Failure	Same as above for O2. Default: 0
No. 19 – O (O1) Auto OFF with Timer	Schedule automatic OFF after set time. Default: 0 (disabled) Value: 1–32535 seconds/ms (see Param 25)
No. 20 – O (O1) Auto ON with Timer	Schedule automatic ON after set time. Default: 0 (disabled)
No. 21 – O2 Auto OFF with Timer	Same as above for O2. Default: 0
No. 22 – O2 Auto ON with Timer	Same as above for O2. Default: 0
No. 23 – O (O1) Contact Type (NO/NC)	Relay contact type. Default: 0 (NO) Value: 1 → NC
No. 24 – O2 Contact Type (NO/NC)	Same as above for O2. Default: 0 (NO)
No. 25 – Set Timer Units for O (O1)	Set timer units: seconds (0) or milliseconds (1). Default: 0
No. 26 – Set Timer Units for O2	Same as above for O2. Default: 0
No. 36 – O (O1) Power Report on Change (%)	Minimum power change to trigger report. Default: 50 Values: 0 (disabled), 1–100 (%)
No. 37 – O2 Power Report on Change (%)	Same as above for O2. Default: 50
No. 39 – Min Time Between Reports (O1)	Minimum interval between reports. Default: 30 Values: 0 (disabled), 1–120s
No. 40 – Min Time Between Reports (O2)	Same as above for O2. Default: 30
No. 91 – Water Alarm	Action on water alarm. Default: 0 (no action) Values: 1 → open relay, 2 → close relay
No. 92 – Smoke Alarm	Action on smoke alarm. Default: 0
No. 93 – CO Alarm	Action on CO alarm. Default: 0
No. 94 – Heat Alarm	Action on heat alarm. Default: 0
No. 120 – Factory Reset	Reset to factory defaults. Default: 0 (do nothing) Value: 1 → perform reset
No. 201–203 – Serial Number Parts	Read-only parts of serial number. Hidden under Advanced tag.

Z-Wave® Command Classes

• ASSOCIATION_V2 [S0, S2]*
• ASSOCIATION_GRP_INFO_V3 [S0, S2]*
• BASIC_V2 [S0, S2]*
• SWITCH_BINARY_V2 [S0, S2]*
• CONFIGURATION_V4 [S0, S2]*
• DEVICE_RESET_LOCALLY_V1 [S0, S2]*
• FIRMWARE_UPDATE_MD_V5 [S0, S2]*
• INDICATOR_V3 [S0, S2]*
• MANUFACTURER_SPECIFIC_V2 [S0, S2]*
• METER_V6 [S0, S2]*
• MULTI_CHANNEL_V4 [S0, S2]*
• MULTI_CHANNEL_ASSOCIATION_V3 [S0, S2]*
• NOTIFICATION_V8 [S0, S2]*
• POWERLEVEL_V1 [S0, S2]*
• SECURITY_V1
• SECURITY_2_V1
• SUPERVISION_V1
• TRANSPORT_SERVICE_V2
• VERSION_V3 [S0, S2]*
• ZWAVEPLUS_INFO_V2

Endpoint 1

• ASSOCIATION_V2 [S0, S2]*
• ASSOCIATION_GRP_INFO_V3 [S0, S2]*
• BASIC_V2 [S0, S2]*
• SWITCH_BINARY_V2 [S0, S2]*
• METER_V6 [S0, S2]*
• MULTI_CHANNEL_V4 [S0, S2]*
• NOTIFICATION_V8 [S0, S2]*
• SECURITY_V1
• SECURITY_2_V1
• SUPERVISION_V1
• ZWAVEPLUS_INFO_V2

Endpoint 2

• ASSOCIATION_V2 [S0, S2]*
• ASSOCIATION_GRP_INFO_V3 [S0, S2]*
• BASIC_V2 [S0, S2]*
• SWITCH_BINARY_V2 [S0, S2]*
• METER_V6 [S0, S2]*
• MULTI_CHANNEL_V4 [S0, S2]*
• NOTIFICATION_V8 [S0, S2]*
• SECURITY_V1
• SECURITY_2_V1
• SUPERVISION_V1
• ZWAVEPLUS_INFO_V2

Note: [S2] = Security S2 Command Class

Z-Wave® Notifications Command Class

Overheat Detected

Field	Value
Comment	Overheat detected
Notification Type Name	Heat Alarm
Type Value	0x04
Event	State
Notification Name	Overheat detected
Name Value	0x02
Version	V2
Device Specific	Yes
LED Signalisation	See table
Device Reaction	Switch OFF all outputs and send notification
Restore Actions	Power cycle, short press S button, press any switch

Over-current Detected (O1, O2, O1+O2)

Field	Value
Comment	Over-current detected
Notification Type Name	Power management
Type Value	0x08
Event	State
Notification Name	Over-current detected
Name Value	0x06
Version	V3
Device Specific	Yes
LED Signalisation	See table
Device Reaction	Switch OFF output(s) and send notification
Restore Actions	Power cycle, short press S button, press any switch

AC Mains Disconnected

Field	Value
Comment	AC mains disconnected (valid for AC/DC)
Notification Type Name	Power management
Type Value	0x08
Event	State
Notification Name	AC mains disconnected
Name Value	0x02
Version	V2
Device Specific	Yes
LED Signalisation	See table
Device Reaction	Switch OFF all outputs and send notification
Restore Actions	Power cycle, short press S button, press any switch

Z-Wave® Associations

Associations enable direct communication between devices without the gateway.

• Max 9 devices per group (recommended ≤5)
• “Lifeline Group” reserved for gateway only (1 node)

Root Device

Association Group 1 – Lifeline

• INDICATOR_REPORT: LED status
• DEVICE_RESET_LOCALLY_NOTIFICATION: triggered upon request
• SWITCH_BINARY_REPORT: status change for all outputs
• NOTIFICATION_REPORT: Overheat
• NOTIFICATION_REPORT: Over-current (sum)
• NOTIFICATION_REPORT: Over-voltage
• NOTIFICATION_REPORT: AC mains disconnected
• METER_REPORT: power consumption (based on Params 36–43)

Group 2

• Assigned to SW (SW1) terminal (Basic command class)
• Triggered by SW (SW1)
• Sends BASIC_SET ON/OFF to associated device

Group 3

• Assigned to SW (SW1) terminal (Switch Multilevel)
• Supports:
  • SWITCH_MULTILEVEL_START_LEVEL_CHANGE
  • SWITCH_MULTILEVEL_STOP_LEVEL_CHANGE

Recommended: use push buttons

Group 4

• Assigned to SW2 terminal (Basic command class)
• Sends BASIC_SET ON/OFF

Group 5

• Assigned to SW2 terminal (Switch Multilevel)
• Supports same commands as Group 3

Recommended: use push buttons

Endpoint 1

Group 1 – Lifeline

• SWITCH_BINARY_REPORT: O1 status
• NOTIFICATION_REPORT: Over-current detected O1
• METER_REPORT: O1 power consumption

Groups 2 & 3

Same as root device (SW1)

Endpoint 2

Group 1 – Lifeline

• SWITCH_BINARY_REPORT: O2 status
• NOTIFICATION_REPORT: Over-current detected O2
• METER_REPORT: O2 power consumption

Groups 2 & 3

Same as root device (SW2)

Z-Wave® Important Disclaimer

Z-Wave® wireless communication may not always be 100% reliable. This Device should not be used in situations where life and/or valuables depend solely on its functioning. If the Device is not recognized by your gateway, manually change the Device type and ensure your gateway supports Z-Wave Plus™ multi-level devices.

Troubleshooting

For troubleshooting, visit our support portal: https://support.shelly.cloud/

Compatibility with Gateways

Gateway	On/Off 1	On/Off 2	SW 1 On/Off	SW 2 On/Off	W 1	W 2	kWh	Notes
Home Assistant	✅	✅	✅	✅	✅	✅	✅
Fibaro HC 3 / Z-Wave engine 3	✅	✅	✅	✅	✅	✅	✅
Homey	✅	✅	✅	✅	✅	✅	✅	Solution
Homee Cube Gen 7	✅	✅	✅	✅	✅	✅	✅
Homee Cube Gen 5	P	P	P	P	P	P	P	*1
SmartThings	✅	✅	✅	✅	✅	✅	✅	With Shelly Wave edge driver
Vera Ezlo	✅	✅	✅	✅	✅	✅	✅
Cozify	✅	✅	✅	✅	✅	✅	✅
Hubitat	⭐	⭐	⭐	⭐	⭐	⭐	⭐

*1 – Device configured as single-channel; one switch controls both outputs simultaneously.

Legend

Symbol	Meaning
✅	Working / Possible
⭐	Not Working / Not Possible
P	Partially
N/T	Not Tested
TBD	To be done

Function Meanings

Function	Meaning
On/Off	Responds to app UI On/Off command
SW On/Off	Reports On/Off changes via SW input
Dimming	Responds to app UI dimming command
SW Dimming	Reports dimming state via SW input
Watts	Reports Watts unsolicited
kWh	Reports kWh unsolicited
Up/Down	Responds to app UI Up/Down command
SW Up/Down	Reports Up/Down changes via SW input
Slats	Slats respond to app UI command
SW Slats	Slats report changes via SW
D control	Reports scene commands (single/double press, etc.) in detached mode
D Binary	Reports binary On/Off via SW input in detached mode
Sensor #	Sensor report visualized in gateway; type in notes

Gateway Guides

You may find useful guides on gateways in the Z-Wave Shelly Knowledge Base.

Compliance

• Wave 2PM multilingual EU Declaration of Conformity 2025-07-22
• Wave 2PM UK PSTI ACT Statement of Compliance

Compliance Archive

• Wave 2PM multilingual EU Declaration of Conformity 11/2023

Printed User Guide

• Wave 2PM Ръководство за потребител и безопасност (Bulgarian)
• Wave_2PM_multilang_2023_print_V4