Shelly Wave Pro 1PM – Device Documentation

Note: The product line known as "Shelly Qubino Wave" will now be referred to as "Shelly Wave". This name change will not impact the functionality of any devices. The only modification will be the use of the new name in all future documentation.

---

Device Identification

• Device: Wave Pro 1PM
• AUS Part number / Ordering Code: QPSW-0A1P16AU
• Z-Wave Product type ID: 0x0002
• Z-Wave Product ID: 0x008B
• Z-Wave Manufacturer: Shelly Europe Ltd.
• Z-Wave Manufacturer ID: 0x0460

---

Terminology

Term	Definition
Device	In this document, the term “Device” refers to the Shelly Qubino device being discussed.
Gateway	A Z-Wave® gateway (also called Z-Wave® controller, main controller, primary controller, or hub) that serves as the central hub for a Z-Wave® smart home network.
S button	The Z-Wave® Service button located on Z-Wave® devices, used for inclusion, exclusion, and factory reset.

---

Short Description

The Wave Pro 1PM is a DIN rail-mounted smart switch with power measurement. It controls the on/off function for one electrical load up to 16 A, and supports both switches (default) and push-buttons.

Switch Connected to Input Terminal SW (SW1)

If configured as a switch (default):

• One toggle: Changes output O (O1) state (on → off, off → on), sends command to associated devices in groups 2 and 3.
• Two toggles within 500ms: Interpreted as "double press", sends command to dimmers, shutters, etc., in groups 2 and 3.

Switch-Memory Connected to Input Terminal SW (SW1)

If configured as switch-memory:

• Close contact: Output O (O1) turns ON and sends command to associated devices in groups 2 and 3.
• Open contact: Output O (O1) turns OFF and sends command to associated devices in groups 2 and 3.

Push-Button Connected to Input Terminal SW (SW1)

If configured as a push-button:

• Short press: Toggles output O (O1) state (on ↔ off), sends command to groups 2 and 3.
• Hold: Sends command to group 3.
• Release: Sends command to group 3.

---

Switching On/Off Load Connected to O (O1)

The load connected to O (O1) can be switched via:

• Z-Wave commands
• Automatic switching (via Parameters No. 19 and 20)
• Pressing the switch/push-button SW (SW1): toggles load state

---

Main Applications

• Residential
• MDU (Multi Dwelling Units: apartments, condos, hotels)
• Light commercial (small offices, retail, restaurants, gas stations)
• Government / Municipal
• University / College

---

Integrations

Shelly Wave devices are built on Z-Wave, the world’s leading smart home technology. They work with all certified gateways supporting the Z-Wave protocol.

We regularly test compatibility across various Z-Wave gateways to ensure full feature support.

---

Simplified Internal Schematics

---

Device Electrical Interfaces

Inputs

• 2 switch/button inputs on screw terminals
• 2 power supply inputs on screw terminals: 2 N (+) and 3 L (−)
• 1 relay input on screw terminal

Outputs

• 1 relay output with power measurement on screw terminal

---

Connectivity

• Z-Wave: Unsecure, S0 Security, S2 Unauthenticated Security, S2 Authenticated Security

---

Safety Features

Overheat Protection

• If temperature exceeds 80°C for more than 5 seconds, the device:
  • Turns off its own relay
  • Sends a Notification Report to the gateway ("Overheat detected")
  • LED reacts accordingly (see LED blinking modes)

Reset conditions:

• Power cycle
• Short press on S button
• Press any switch/push-button on SW (SW1, SW2, etc.)

✅ Note: Overheat protection is always active and cannot be disabled.

More details: Notification for Overheat Detected

---

Overcurrent Protection

• If current exceeds 16A + 10% (17.6A) for more than 5 seconds, the device:
  • Turns off its relay
  • Sends a Notification Report ("Over-current detected")
  • LED blinks accordingly

Reset conditions:

• Power cycle
• Short press on S button
• Press any switch/push-button on SW (SW1, SW2, etc.)

✅ Note: Overcurrent protection is always active and cannot be disabled.

More details: Notification for Over-current Detected

---

Overvoltage Protection

• Valid for standard 230 V AC supply.
• If voltage exceeds 278 V AC (240V +15%) for more than 5 seconds, the device:
  • Turns off its relay
  • Sends a Notification Report ("Overvoltage detected")
  • LED blinks accordingly

Reset conditions:

• Power cycle
• Short press on S button
• Press any switch/push-button on SW (SW1, SW2, etc.)

✅ Note: Overvoltage protection is always active and cannot be disabled.

More details: Notification for Overvoltage Detected

---

Supported Load Types

• Resistive (incandescent bulbs, heating devices)
• Capacitive (capacitor banks, electronic equipment, motor start capacitors)
• Inductive with RC Snubber (LED drivers, transformers, fans, refrigerators, air conditioners)

---

User Interface

S Button and Operating Modes

1. Normal mode
2. Setting in progress mode
3. Setting mode (with S button)
   • Used for inclusion, exclusion, factory reset, etc.
   • Limited duration; automatically reverts to Normal mode after procedure.

Entering Setting Mode:

• Quickly press and hold the S button until the LED turns solid blue.
• Additional quick press → cycles through menu options.
• Menu timeout: 10 seconds before returning to Normal mode.

---

S Button Functions

• Manually add device to Z-Wave network
• Manually remove device from Z-Wave network
• Factory reset device

---

LED Signalisation

Mode	Status	Meaning
Mode 1	0.5s On / 2s Off	Normal operation (blue = excluded, green = included)
Mode 2	0.5s On / 0.5s Off	Adding/removing, OTA update, power check
Mode 3	0.1s On / 0.1s Off	Executing action (add/remove/factory reset)
Mode 4	(1–7 times) 0.2s On/Off + 2s Off	Alarm states (overcurrent, overheat, overvoltage, etc.)
Mode 5	0.2s On blue / 0.2s On red	Power supply check (AC frequency or DC voltage)

Alarm LED Patterns:

Alarm	Pattern	Description
Overcurrent detected	1x: 0.2s On / 0.2s Off, 2s Off	Repeats
Overheat detected	2x: 0.2s On / 0.2s Off, 2s Off	Repeats
Power supply fault	3x: 0.2s On / 0.2s Off, 2s Off	Repeats
Overvoltage detected	7x: 0.2s On / 0.2s Off, 2s Off	Repeats

🔔 All alarms trigger relay OFF and send notification to gateway.

---

Specifications

⚠️ Error rendering macro 'excerpt-include': User does not have permission to view the page 'DEV:Technical Specifications'.

---

Basic Wiring Diagram

---

Legend

Terminal	Function	Wire	Purpose
N	Neutral terminal	N	Neutral wire
L	Live terminal (110–240 V AC)	L	Live (110–240 V AC) wire
SW1	Switch/push-button input (controls O)	—	Control input
SW2	Switch/push-button input	—	Optional control input
I	Load circuit input	—	Input side of load
O	Load circuit output	—	Output side of load

---

About Z-Wave®

Adding the Device to a Z-Wave® Network (Inclusion)

⚠️ Note: All outputs (O, O1, etc.) will briefly turn on/off during successful inclusion/exclusion.

SmartStart Inclusion

1. Scan QR code on device label using gateway app.
2. Add DSK to provisioning list.
3. Connect device to power.
4. Blue LED blinking in Mode 1 → not added.
5. Auto-inclusion starts within seconds.
6. Blue LED blinks in Mode 2 during process.
7. Green LED blinks in Mode 1 if successful.

Adding with S Button

1. Connect device to power.
2. Check blue LED blinking in Mode 1.
3. Enable add/remove mode on gateway.
4. Press and hold S button until LED turns solid blue.
5. Release, then press & hold (>2s) until LED blinks in Mode 3 → Learn mode starts.
6. Blue LED blinks in Mode 2 during adding.
7. Green LED blinks in Mode 1 if successful.

⏱️ Setting mode timeout: 10 seconds

Adding with Switch/Push-Button

1. Connect device to power.
2. Confirm blue LED blinking in Mode 1.
3. Enable add/remove mode on gateway.
4. Toggle SW terminal 3 times within 3 seconds → puts device in Learn mode.
5. Blue LED blinks in Mode 2 during process.
6. Green LED blinks in Mode 1 if successful.

📌 Learn mode: State allowing device to receive network info from gateway.

---

Removing the Device from a Z-Wave® Network (Exclusion)

⚠️ Note: Custom settings remain unchanged; only network association is removed.

Removing with S Button

1. Connect device to power.
2. Confirm green LED blinking in Mode 1 → device is added.
3. Enable add/remove mode on gateway.
4. Press and hold S button until LED turns solid blue.
5. Release, then press & hold (>2s) until LED blinks in Mode 3 → Learn mode starts.
6. Blue LED blinks in Mode 2 during removal.
7. Blue LED blinks in Mode 1 if successful.

⏱️ Setting mode timeout: 10 seconds

Removing with Switch/Push-Button

1. Connect device to power.
2. Confirm green LED blinking in Mode 1.
3. Enable add/remove mode on gateway.
4. Toggle SW terminal 3 times within 3 seconds → Learn mode.
5. Blue LED blinks in Mode 2 during removal.
6. Blue LED blinks in Mode 1 if successful.

---

Factory Reset

General

After reset, all custom parameters (kWh, associations, routing, etc.) revert to default. HOME ID and NODE ID are deleted.

💡 Use only when gateway is missing or inoperable.

With S Button

1. Press and hold S button until LED turns solid blue.
2. Press S button repeatedly until LED turns solid red.
3. Press and hold (>2s) S button until red LED blinks in Mode 3 → reset begins.
4. During reset: LED turns solid green (~1s), then blue/red blink in Mode 3 (~2s).
5. Blue LED blinking in Mode 1 indicates success.

With Switch/Push-Button

⚠️ Only possible within first minute after power-up.

1. Connect device to power.
2. Toggle SW terminal 5 times within 3 seconds.
3. LED turns solid green (~1s), then blue/red blink in Mode 3 (~2s).
4. Blue LED blinking in Mode 1 indicates success.

Remotely via Parameter No. 120

Set Parameter 120 to 1431655765 (hex 0x55555555) to trigger remote factory reset.

✅ After reset, parameter resets to 0.

---

Z-Wave® Security and Device Specific Key (DSK)

• Supports Security 2 (S2) with AES-128 encryption.
• Requires S2-enabled gateway for full security.
• Uses Out-of-Band DSK authentication.
• PIN Code (first 5 digits) required during S2 inclusion.

📌 DSK Label Example:

• Printed on device side and inside packaging.
• Include QR code for scanning.
• Do not remove label.

🔐 Important: Never lose the DSK label.

---

Z-Wave® Parameters

Parameter	Description	Default	Values
1 – SW (SW1) Switch Type	Defines behavior of switch on SW1	2	0: momentary, 1: toggle (contact closed=ON), 2: toggle (state changes)
2 – SW2 Switch Type	Same for SW2 terminal	2	0: momentary, 1: toggle (closed=ON), 2: toggle (state changes)
17 – Restore State After Power Failure	Save last state after outage?	0	0: yes, 1: no (remains off)
19 – Auto OFF Timer (O1)	Schedule auto-off after ON	0	0: disabled, 1–32535: sec or ms (see Param 25)
20 – Auto ON Timer (O1)	Schedule auto-on after OFF	0	0: disabled, 1–32535: sec or ms
23 – O (O1) Contact Type	Relay contact: NO or NC	0	0: NO, 1: NC
25 – Timer Units (sec/ms)	Set timer resolution	0	0: seconds, 1: milliseconds
36 – Power Report Change (%)	Min % change to report power	50	0: disabled, 1–100%
39 – Min Time Between Reports (O1)	Min interval between reports	30	0: disabled, 1–120 seconds
91 – Water Alarm Response	Action on water alarm	0	0: none, 1: open relay, 2: close relay
92 – Smoke Alarm Response	Action on smoke alarm	0	0: none, 1: open, 2: close
93 – CO Alarm Response	Action on CO alarm	0	0: none, 1: open, 2: close
94 – Heat Alarm Response	Action on heat alarm	0	0: none, 1: open, 2: close
120 – Factory Reset	Trigger reset	0	0: no, 1431655765 (0x55555555)
201–203 – Serial Number Parts	Read-only, hidden	Device-specific	0x00000000 – 0x7FFFFFFF

---

Z-Wave® Command Classes

Class	Security
ASSOCIATION_V2	[S0, S2]*
ASSOCIATION_GRP_INFO_V3	[S0, S2]*
BASIC_V2	[S0, S2]*
SWITCH_BINARY_V2	[S0, S2]*
CONFIGURATION_V4	[S0, S2]*
DEVICE_RESET_LOCALLY_V1	[S0, S2]*
FIRMWARE_UPDATE_MD_V5	[S0, S2]*
INDICATOR_V3	[S0, S2]*
MANUFACTURER_SPECIFIC_V2	[S0, S2]*
METER_V6	[S0, S2]*
MULTI_CHANNEL_ASSOCIATION_V3	[S0, S2]*
NOTIFICATION_V8	[S0, S2]*
POWERLEVEL_V1	[S0, S2]*
SECURITY_V1	—
SECURITY_2_V1	—
SUPERVISION_V1	—
TRANSPORT_SERVICE_V2	—
VERSION_V3	[S0, S2]*
ZWAVEPLUS_INFO_V2	—

[S2] = Security S2 Command Class

---

Z-Wave® Notifications Command Class

Overheat Detected

Field	Value
Notification Type Name	Heat Alarm
Value	0x04
Event	State
Notification Name	Overheat detected
Value	0x02
Version	V2
Device Specific	Yes
LED Signalisation	See table
Device Reaction	Turn off output, send notification
Restore Action	Power cycle, S button press, SW press

Over-current Detected O (O1)

Field	Value
Notification Type Name	Power management
Value	0x08
Event	State
Notification Name	Over-current detected
Value	0x06
Version	V3
Device Specific	Yes
LED Signalisation	See table
Device Reaction	Turn off O(1), send notification
Restore Action	Power cycle, S button press, SW press

AC Mains Disconnected

Field	Value
Notification Type Name	Power management
Value	0x08
Event	State
Notification Name	AC mains disconnected
Value	0x02
Version	V2
Device Specific	Yes
LED Signalisation	See table
Device Reaction	Turn off all outputs, send notification
Restore Action	Power cycle, S button press, SW press

---

Z-Wave® Associations

Group	Nodes	Trigger	Commands	Notes
1 (Lifeline)	1 (Gateway)	Status, errors	INDICATOR_REPORT, DEVICE_RESET_LOCALLY_NOTIFICATION, SWITCH_BINARY_REPORT, NOTIFICATION_REPORT, METER_REPORT	Standard lifeline
2	9	SW1 (On/Off)	BASIC_SET ON/OFF	For basic switch control
3	9	SW1 (Dimming)	SWITCH_MULTILEVEL_START_LEVEL_CHANGE / STOP	For dimmer/slats
4	9	SW1 (On/Off)	BASIC_SET ON/OFF	Duplicate of group 2
5	9	SW1 (Dimming)	SWITCH_MULTILEVEL_START_LEVEL_CHANGE / STOP	Duplicate of group 3

---

Z-Wave® Important Disclaimer

Z-Wave® communication may not be 100% reliable. Do not rely solely on this device for life-critical applications. If the device isn't recognized, manually change the device type and confirm gateway supports Z-Wave Plus™ multi-level devices.

---

Troubleshooting

For help, visit: Shelly Support Portal

---

Compatibility with Gateways

Gateway	On/Off	SW On/Off	Watts	kWh	Notes
Home Assistant	✅	✅	✅	✅
Fibaro HC3 / Z-Wave engine 3	✅	✅	✅	✅
Homey	✅	✅	✅	✅
Homee Cube Gen 7	✅	✅	✅	✅
Homee Cube Gen 5	✅	⚠️ P*1	⚠️ ★*2	⚠️ ★*2	*1 UI doesn’t reflect updates *2 W/kWh not reported
SmartThings	✅	✅	✅	✅	With Shelly Wave edge driver
Vera Ezlo	✅	✅	✅	✅
Cozify	✅	✅	✅	✅

🔍 Legend:

• ✅ = Working / Possible
• ⚠️ ★ = Not working / Not possible
• ⚠️ P = Partially
• N/T = Not Tested
• TBD = To Be Done

---

Gateway Guides

Useful guides: Shelly Knowledge Base – Z-Wave

---

Compliance

• Wave Pro 1PM Multilingual EU Declaration of Conformity (2025)
• Wave Pro 1PM UK PSTI ACT Statement of Compliance

---

Printed User Guide

Download PDF: Wave_Pro1PM_multilang_2023_print_V1.pdf